Ashtray replacement - airbag cubby ....

Ashtray replacement - airbag cubby .... was created by Dan1971

Posted 10 months 3 weeks ago #218471
So I'm after an airbag cubby hole - smokestone
And something like this to replace the ashtray - 
 
 
by Dan1971

Please Log in or Create an account to join the conversation.

  • Red110
  • Away
  • Qualified MGer
  • Qualified MGer
    Site Supporter
  • Posts: 559
  • Thanks: 153

Replied by Red110 on topic Ashtray replacement - airbag cubby ....

Posted 10 months 3 weeks ago #218473
I got that box at a web site  that I mentioned where you saw that pic. Don’t know why I can’t reach that page.

Alec here is 3Doing something similar, I think
by Red110

Please Log in or Create an account to join the conversation.

  • Alec
  • Offline
  • Time served MGer
  • Time served MGer
    Site Supporter
  • Posts: 410
  • Thanks: 81

Replied by Alec on topic Ashtray replacement - airbag cubby ....

Posted 10 months 3 weeks ago #218474
I am indeed, and printing some as i type this, thanks for the mention
by Alec

Please Log in or Create an account to join the conversation.

Replied by Dan1971 on topic Ashtray replacement - airbag cubby ....

Posted 10 months 2 weeks ago #218576
So thanks to Alec - appears the ashtray replacement is addressed - but still on the lookout for a cubby...
by Dan1971
The following user(s) said Thank You: Mark63

Please Log in or Create an account to join the conversation.

Replied by Mark63 on topic Ashtray replacement - airbag cubby ....

Posted 10 months 2 weeks ago #218583
I`ve just bought a spare blank for £13 , so I`m going to have a go at making my own .
by Mark63

Please Log in or Create an account to join the conversation.

  • Alec
  • Offline
  • Time served MGer
  • Time served MGer
    Site Supporter
  • Posts: 410
  • Thanks: 81

Replied by Alec on topic Ashtray replacement - airbag cubby ....

Posted 10 months 2 weeks ago #218584
Dan pm sent mate
 
by Alec
The following user(s) said Thank You: Dan1971

Please Log in or Create an account to join the conversation.

Replied by Airportable on topic Ashtray replacement - airbag cubby ....

Posted 10 months 2 weeks ago #218588
The first iteration of this idea used a cubby of a Rover 25 (iirc) & that goes back some way. I have dual airbags & so this is of little practical interest other than passing. It is however an interesting project; any project is interesting if there is a practical outcome.
M
by Airportable

Please Log in or Create an account to join the conversation.

  • Alec
  • Offline
  • Time served MGer
  • Time served MGer
    Site Supporter
  • Posts: 410
  • Thanks: 81

Replied by Alec on topic Ashtray replacement - airbag cubby ....

Posted 10 months 2 weeks ago #218592
Was it a direct fit Mike?
by Alec

Please Log in or Create an account to join the conversation.

Replied by Airportable on topic Ashtray replacement - airbag cubby ....

Posted 10 months 2 weeks ago #218593
As far as I recall it wasn’t but not that far off. It was covered on here, by whole & just when I don’t recall, a search 👀 should turn up the article.
I’d have a look myself, however I’ve taken the log burner out & am in no fit state to spend time looking back. I usually end up finding an article I wrote years back & am overcome with embarrassment.
M
by Airportable

Please Log in or Create an account to join the conversation.

Replied by Dan1971 on topic Ashtray replacement - airbag cubby ....

Posted 10 months 1 week ago #218836
All done and fitted. 

 
by Dan1971
The following user(s) said Thank You: Mark63

Please Log in or Create an account to join the conversation.

  • Alec
  • Offline
  • Time served MGer
  • Time served MGer
    Site Supporter
  • Posts: 410
  • Thanks: 81

Replied by Alec on topic Ashtray replacement - airbag cubby ....

Posted 10 months 1 week ago #218838
did you get that from Robert Dan?
by Alec

Please Log in or Create an account to join the conversation.

Replied by Dan1971 on topic Ashtray replacement - airbag cubby ....

Posted 10 months 1 week ago #218840
Yes...
by Dan1971

Please Log in or Create an account to join the conversation.

Time to create page: 0.450 seconds